Drum overhead microphone technique comparison

Drum overhead microphone technique comparison - at RECORDINGHACKS.com

ORTF PairYou have two microphones and two hours. How many ways can you mike a drum kit?

I had a good idea of my choices, but I wanted to hear them all together so I would know what works in my room. It’s no different from getting to know your own mic locker; each stereo mic placement technique is a tool, and like any tool it is only useful if you know how to use it.

I made a list of seven stereo mic techniques for drum recording, then recorded myself playing the same thing on the same drums in the same room, as heard through the same pair of microphones — in seven different configurations. Following is a detailed comparison of Spaced Pair (omni and cardioid), Coincident Pair (omni and cardioid), ORTF, Mid-Side and “Recorderman.”

The mics in question were a pair of 4400aSE Electronics’ 4400a. The 4400a is an incredibly versatile large-diaphragm multipattern FET condenser in a very small form-factor. (We are liking this mike a lot; watch for a full review soon.)

The audio samples below are stereo 320kbps MP3s. I recommend listening in headphones, as the differences among the tracks are easiest to hear if the sound of your own monitoring environment is well-controlled.

Listening with the proper mindset

All the following are legitimate stereo miking techniques. While you might find a favorite here, be aware that the appropriate technique for any session depends on the drums, the room, the player, the song, and the arrangement. As always.

Nonetheless, this test reveals characteristics of each OH miking technique — such as the width of the stereo field, the intimacy of the kit, the amount of room sound in the mix, the susceptibility to phasing or comb-filtering problems — that bear consideration for every session.

XY (Coincident Pair)

 XY or Coincident Pair
Cardioid:

Omni:

XY is one of the two most common stereo overhead miking techniques. For my test, the mics were in a 90° spread, about 55'' from the center of the snare head and 80'' above the floor. I recorded samples in both Cardioid and Omnidirectional modes.

Neither of these clips presents a wide stereo image. Listen to the closing tom fill — there is little discernible lateral movement.

The image collapses to mono gracefully; this is expected, given that the mic capsules were close together. Listening in mono also reveals that, in stereo, both clips do present a sense of space — it’s small, but it’s there. If you don’t like hearing tom fills that go from one corner of the room to the other, or if you’re recording a song for which the drums play a background role, then XY is a reliable choice.

For me, both these tracks have too much boomy low end. I don’t much like either of them.

The omni clip has far too much room sound for my taste. In a space that is either deader or tuned, I think omni is a more viable choice for drum overheads; for example, listen to the omni tracks in my old drum overhead shootout, in which an omni mic brought depth and LF without excessive boom or smeary HF.

Note, too, that the height of the XY pair will alter the sound of the result. I think I would have liked this pair better if I’d lowered the mics to a height of about 60 inches (instead of 80); this would have reduced the apparent volume of the room sound, and provided more stereo separation too.

Spaced Pair

 Spaced Pair
Cardioid:

Omni:

The spaced pair is the other of the most common overhead drum miking techniques, although there are an infinite variety of ways to do it.

Perhaps more than any other method tested, the spaced pair approach requires care to avoid phasing problems. As an example, let’s say the snare drum resonates at 400Hz. The wavelength of a 400Hz tone is about 33 inches. If one of a pair of haphazardly-placed OH mics is 16.5 inches closer to the snare than the other, then the snare sound will arrive out-of-phase at the two mics, and in mono the 400Hz tone won’t be heard.

While it’s true that drums resonate at multiple frequencies, phasing problems can nonetheless cause drums to sound thin.

The easiest way to avoid screwing up the snare sound with phasing problems is to put the two capsules of the spaced pair at equal distances from the center of the snare head. This has the added benefit of centering the snare in the stereo image, which is most likely where you want it anyway.

To be fair, this arrangement may well introduce phasing problems with the kick or toms, which is why the OH mic position should always be tested before recording.

The 3:1 rule suggests that the mics should be three times farther apart than their height above the drum kit. In practice, I see engineers worrying more about the distance from the snare than the distance between the mics. Use your ears (and a tape measure too).

Should the mics’ capsules be pointed straight down, angled in, angled out, or aimed directly at the snare? It’s a matter of taste. Any drums or cymbals that are on-axis — meaning, in the mics’ “line of sight” — are going to be more clearly heard and probably louder too. Adjust the OH position with an ear toward your final mix.

In this test, the mics were 69'' from the floor, 52'' from the center of the snare, and 58'' apart, with the capsules pointing straight down. I recorded samples in both Cardioid and Omnidirectional modes.

The Cardioid clip gives a wide stereo image. The hi-hat is firmly on the left. The tom fill has some movement, although it seems to start in the middle move to the right. (The panning of close tom mics could of course alter this perception.)

I like the sound of the Cardioid pair; the drums retain their presence without losing the sound of the room. I can hear the space, but I can hear the drums too. It’s a good balance.

In Omni, the mics bring in more of the sound of the room, but not so much as in XY. This is probably a result of the fact that in XY, the mics were mostly pointing past the drums. But while this Omni track doesn’t offend me, I’d be more likely to choose Cardioid for most applications, and rely on room mics for the room sound.

ORTF

 ORTF

ORTF is a curious stereo technique with specific positioning requirements: 17cm between capsules, angled 110° apart. I fudged this slightly, owing to haste and my unfortunate reliance on the World’s Worst Stereo Mic Bar (produced by On-Stage Stands). Note that the 4400a stereo kit includes a far superior stereo bar that I wish I’d used instead. Alas.

My ORTF pair was 77'' above the floor, 53'' above the snare, positioned so the snare was equidistant from the two mics’ capsules.

The sound of this track grew on me over repeated listenings. The drums sound big, but not excessively boomy. The cymbals are well-represented without taking anyone’s face off.

The stereo image is not as wide as on the Spaced Pair track, but ORTF sounds more realistic — see below for a head-to-head comparison of ORTF vs. Spaced Pair.

I don’t hear any drastic volume changes when I monitor the ORTF track in mono; this suggests a lack of significant phase problems.

I think I’d like ORTF even better if the mics were lower.

Mid-Side

 Mid-SideThe following two clips are of the same performance; the only difference is a mix-time gain change.

Narrow:

Wide:

Mid-Side is a stereo technique that promises perfect mono compatibility. It employs a “mid” Cardioid mic pointed at the source, and a “side” figure-of-8 mic whose null is pointed at the source. The stereo “left” channel is the mid plus the side, while the “right” channel is the mid minus the side… more or less. (Read more about mid-side technique.)

One of the benefits of mid-side is that adjusting the relative gain of the two signals can alter the perceived width of the stereo image. The louder the “side” channel is, the wider the stereo image is. That said, the side channel is comprised entirely of off-axis sounds, which might not sound very good, depending on the instrument and room.

My MS pair was located 71'' above the floor, with the “mid” capsule about 52'' from the center of the snare. I produced two samples; the difference between “narrow” and “wide” is about 8dB worth of gain on the side channel. (The mid channel is about 9dB (RMS) louder than the side channel in the “wide” mix, and about 17dB louder than the side channel in the “narrow” mix.)

The “narrow” mix sounds a lot like XY! The XY track contains more of the sound of the room, due to the height of the XY pair. But the stereo image is similar in size.

Flipping to mono, the “narrow” track sounds almost the same as in stereo. There is not much side-channel information in this mix.

The “wide” track communicates a greater sense of space, but the change is subtle. And it’s not true stereo separation to my ear; rather, the size of the space seems to grow, and the size of the kit seems to grow, but I don’t hear the high-hats or floor tom move farther to the outside of the mix.

Mono compatibility is excellent for both these tracks, as expected.

But I’m not fond of this sound. Part of the problem is that the “side” channel sounds like a room mic, not like an overhead; I’d rather my stereo image not come at the cost of trashing up the sound of the kit. But as with the Omni samples above, Mid-side would likely work better in a treated room.

Recorderman

 Recorderman

The “Recorderman” technique is a close-overhead technique that attempts to put both mics equidistant from both the snare and the kick drum. One mic stands about 32'' above the snare, pointing straight down, while the other sits over the drummer’s right shoulder, pointing at the snare. Here’s a video tutorial.

I panned the two tracks hard R/L in this clip, which maximizes the width of the stereo image at the cost of leaving a hole in the middle. Listen to the closing tom fill; it sort of jumps from left to right. But of course this is easy to adjust at mix time.

This clip sounds unlike every other clip on this page. It’s punchy, clean, and very dry. All that room sound from the other samples is gone, because the mics are nearly half the distance from the drums as before. (Hello, inverse-square law!)

This sound puts me in the middle of the kit. I love the presence of this sound. The kick drum is tighter-sounding here than in any other clip.

But is it too dry?

Head to head

I extracted a 4-bar clip from each of the cardioid-pattern samples, and pasted them into one file, arranged from narrowest to widest stereo field (a subjective judgment, of course). In order, they are:

  1. XY
  2. Mid-side
  3. Recorderman
  4. ORTF
  5. Spaced Pair

The tonal difference is eye-opening. Compare the sound of the cymbal in the first two sections; the XY clip contains much more cymbal ring than does the MS clip. Then hear how the cymbals drop away in the third section (Recorderman) — a much drier, more drum-centric OH configuration.

The ORTF clip sounds tonally similar to Recorderman, but has a wider stereo image. The spaced pair clip is wider still, but introduces a tonal change that I’m not fond of.

XY vs Spaced Pair

The next comparison illustrates the stereo field differences between XY and spaced pair, with both mics in Cardioid mode. This clip contains a 1-bar excerpt from the XY sample, then Spaced, and then the whole thing repeats.

I far prefer the spaced-pair approach. The drum kit, unlike just about every other instrument on stage, is naturally a stereo instrument. (And personally, I do like those big Neil Peart tom fills that go from one corner of the room to another!)

ORTF vs Spaced Pair

The next comparison reveals the stereo field differences between ORTF and Spaced Pair. Just to keep things confusing, this time the excerpts are 2 bars long: a 2-bar clip in ORTF, then Spaced, then ORTF again, then Spaced again.

As mentioned above, the sound of ORTF grew on me. It’s not as wide as the Spaced Pair image, but it sounds more realistic. Although I liked the Spaced Pair track in isolation, when I compare it to ORTF, it seems unnatural.

Personal Preferences

The “Recorderman” technique has been my go-to OH technique for years, so it is familiar, and a welcome change from what was sounding like excessively room-y overhead tracks. I really like the sound of it, and I like that the mics can be close to the kit without being in the way.

But the ORTF results sounded really good, too, and promise an easier setup. Two mics on a single stand can easily be moved around in space to quickly find a sweet spot for height and angle. I’ll definitely be trying ORTF more in the future.

What about Glyn Johns?!

The most obvious missing drum mic technique here is the “Glyn Johns” method, about which more can be read here. I skipped it primarily because it is not a stereo overhead technique — it’s a 4-mic approach for the whole drum kit.

Certainly any of the OH techniques I tried would likely be augmented by close mics on the kick and snare, and possibly tom mics and ambient mics too. But all the techniques I tested give a usable representation of the kit. I’m not sure that would be true with one-half of the Glyn Johns approach.

I also didn’t try a Jecklin disk. I’ve never seen anyone record drums that way, but it sounds like fun. Maybe next time.

Conclusions

A few useful lessons emerged from this process:

  • A pair of cardioid mics provides several distinct, viable OH sounds.
  • If the mic placement puts the whole drum kit off-axis, the OH sound will be primarily the sound of the room.
  • The closer the mics are to the kit, the less room sound you’ll hear (and the less preamp gain you’ll need).
  • Avoid phase issues by keeping the snare and kick centered between the mics.
  • XY and mid-side create the narrowest stereo image; ORTF and spaced pair create a wider image.
  • Reduce cymbal volume (and room sound) via Recorderman.

As always, the main takeaway is “Test and listen!” But you knew that already.

I’d like to hear your lessons, too: is your go-to OH technique dependent on the room, the size of the kit, the style of music? Are there “gotchas” not already listed here? When the drummer can’t stop pounding the hell out of the cymbals, is it acceptable to simply move them out of his reach? The comments are open!

 

 

[Alan uutisia]